Miele G 6994 Operating Instructions Manual Download Page 86

Page: 86 / 116

Problem solving guide

Problem

Possible cause and remedy

White residue is visible
on cutlery and crockery,
clouding occurs on
glassware; film can be
wiped off.

Not enough rinse aid was used.



Increase the dosage (see "Settings menu - Rinse
aid").

There is no salt in the salt reservoir.



Fill the salt reservoir (see "Before using for the first
time - Dishwasher salt").

An unsuitable combination detergent has been used.



Change your detergent. Use a standard liquid,
tablet or powder detergent, and fill the salt and
rinse aid reservoirs in the dishwasher.

The water softener is programmed to too low a water
hardness level.



Programme the water softener to a higher water
hardness level (see "Settings menu - Water
hardness").

There are rust stains on
cutlery.

The affected items are not corrosion resistant.



There is no remedy.
Purchase cutlery which is dishwasher-proof.

A programme was not run after dishwasher salt was
added. Traces of salt have got into the wash cycle.



Always run the

QuickPowerWash

programme with

the

Short

programme option selected and without

any crockery in the dishwasher after adding
dishwasher salt.

Summary of Contents for G 6994





















































































































Search results

Summary of Contents for G 6994

Reviews:

Related manuals for G 6994

Brands by name

Popular brands

Miele G 6994, Operating Instructions Manual

Search results

Summary of Contents for G 6994

Reviews:

Related manuals for G 6994

Brands by name

Popular brands