Miele G 6994 Operating Instructions Manual Download Page 53

Page: 53 / 116

Operation

Switching on



Turn on the tap if it is turned off.



Open the door.



Make sure the spray arms are not
obstructed.



Switch the dishwasher on using the



sensor.

The main menu will appear in the
display.

Switch the

Memory

function on (see

"Settings menu, Memory") if you want
the last programme used to appear in
the display instead of the main menu.

Selecting a programme

Choose your programme according to
the type of load and how dirty it is.

The different programmes and their
uses are described in the

Programme

chart

later on in this booklet.



Use the



arrow sensors to select

a programme and confirm with the

sensor.

The display will change to show the
programme menu.

Touch the



sensor to call up more

information about the programme
currently selected.

You can now select Extras for your
programme (see "Programme options").

To select a different programme, touch
the



sensor to return to the main

menu.

Summary of Contents for G 6994





















































































































Search results

Summary of Contents for G 6994

Reviews:

Related manuals for G 6994

Brands by name

Popular brands

Miele G 6994, Operating Instructions Manual

Search results

Summary of Contents for G 6994

Reviews:

Related manuals for G 6994

Brands by name

Popular brands