MG Gloster Manual Download Page 68

Page: 68 / 264

BEFORE YOU DRIVE

ESP (Electronic Stability Program) Indicator Lamp

When the ignition switch is turned to the ON position, "ESP

Indicator Lamp (yellow) illuminates, the system conducts the self-check

and the lamp goes off after several seconds.

"ESP Indicator Lamp (yellow)” blinks when the electronic stability

program is operating.

If the warning lamp remains on, it indicates that the electric stability

program has a malfunction, please contact Service Dealer for service as

soon as possible. Please Refer to "Brake System" in the Starting and

Driving section for more information.

ESP (Electronic Stability Program) OFF Indicator Lamp

When the ignition switch is place in ON position, the "ESP

OFF Indicator Lamp (yellow)" illuminates, the system conducts the self-

check and the lamp goes out after several seconds.

When the ESP OFF switch is pressed and the ESP is turned off, "ESP OFF

Indicator Lamp (yellow)" illuminates. Please Refer to "Floor Console

Switches" in this section for more information.

Hill Descant Indicator Lamp

Engine Malfunction Warning Lamp

Emission MIL

When the Hill Descent is turned on and the operating

conditions are met, the "Hill Descent Indicator Lamp (green)" blinks.

Refer to "Floor Console Switches" in this chapter for information on the

hill descent switch. If the Hill Descent system fails, the "Hill Descent

Indicator Lamp (yellow)" illuminates.

Please Refer to "Brake System" in the Starting and Driving section for

more information.

When the ignition switch is turned to the ON position,

"Engine Malfunction Warning Lamp (yellow)" illuminates, the system

conducts the self-check and the lamp goes off after several seconds.

If the warning lamp illuminates, it indicates that the engine-related parts

are faulty. Please contact our Service Dealer for service as soon as

possible.

When the ignition switch is turned to the ON position,

"Emission MIL (yellow)" illuminates, and goes off after the engine is

started. If the warning lamp illuminates, it indicates that the engine

performance and the emission system are faulty. Please contact Service

BEFORE YOU DRIVE

Dealer for service as soon as possible, meanwhile, avoid the too high

engine speed or fast acceleration.

Even if the oil level is normal, do not restart the engine, please

contact Service Dealer for service as soon as possible.

Oil Pressure Warning Lamp

When the ignition switch is turned to the ON position, “Oil

Pressure Warning Lamp (red)” illuminates, the system conducts the

self-check and the lamp goes off after several seconds. After the engine

is started or during the driving, the “Oil Pressure Warning Lamp (red)"

illuminates, it indicates that the oil pressure is faulty, please shut down

the engine immediately and check the oil level. Refer to “Engine Oil” in

the Maintenance and Service chapter.

Engine lmmobiliser Warning Lamp

When the ignition switch is turned to the ON position,

“Engine lmmobiliser Warning Lamp (yellow)” illuminates, the system

conducts the self-check and the lamp goes off after several seconds. If

the engine immobiliser is authenticated successfully, "Engine

lmmobiliser Warning Lamp (yellow)" remains dark and the engine can

be started. If the "Engine lmmobiliser Warning Lamp (yellow)• blinks, it

indicates that the immobiliser control system has a malfunction, the

engine can not be started, please contact Service Dealer for service

immediately.

Body Theft Deterrent Warning Lamp

When the vehicle is in the armed state, "Body Theft

Deterrent Warning Lamp (red)” blinks.

When the vehicle is out of the armed state, "Body Theft Deterrent

Warning Lamp (red)" goes off.

If the theft deterrent alarm is triggered, the "Body Theft Deterrent

Warning Lamp (red)" blinks, accompanied with audible and visible alarm.

When the ignition switch is turned to the ON position, "Tyre

Pressure Monitoring System Warning Lamp (yellow)" illuminates, the

system conducts the self-check and goes off after several seconds.

When the tyre pressure monitoring system has a malfunction, "Tyre

Pressure Monitoring System Warning Lamp (yellow)" illuminates, please

contact Service Dealer for service as soon as possible.

Tyre Pressure Monitoring System Warning Lamp

Caution

Summary of Contents for Gloster









































































































































































































































































Search results

Summary of Contents for Gloster

Reviews:

MG Gloster, Manual, Page: 68 / 264

Search results

Summary of Contents for Gloster

Reviews: