Mercedes-Benz Comand MY11 Page 3 Operating Instructions Manual Download

Page: 3 / 194

Welcome to the world of Mercedes-Benz
First of all, familiarize yourself with the

COMAND control panel and read this manual

thoroughly before driving off. This will help

you to obtain the maximum pleasure from

your COMAND control panel and to avoid

endangering yourself and others.
Depending on the model and equipment level,

the functions and equipment of your

COMAND control panel may deviate from

some descriptions and illustrations.
Mercedes-Benz is constantly updating its

systems to the state-of-the art and reserves

the right to introduce changes to the design,

equipment and technical features.
You cannot, therefore, base any claims on the

data, illustrations or descriptions in this

manual.
If you have any further questions, please

contact an authorized Mercedes-Benz

Center.
This manual is an integral part of the vehicle.

You should always keep it in the vehicle and

pass it on to the new owner if you sell the

vehicle.
The technical documentation team at

Daimler AG wishes you safe and pleasant

motoring.

2125846681

É2125846681.ËÍ

Summary of Contents for Comand MY11



































































































































































































Search results

Summary of Contents for Comand MY11

Reviews:

Related manuals for Comand MY11

Brands by name

Popular brands

Mercedes-Benz Comand MY11, Operating Instructions Manual

Search results

Summary of Contents for Comand MY11

Reviews:

Related manuals for Comand MY11

Brands by name

Popular brands