Mercedes-Benz Comand MY11 Page 176 Operating Instructions Manual Download

Page: 176 / 194

Cordless headphones

Overview

Volume control

;

To select a screen for the headphones

Battery compartment cover

To switch the cordless headphones on/off

Indicator lamp with various displays (

page 174)

Open both sides of the headphones and adjust the fit of the headphones by pulling the

headphone band in the direction of the arrow.

Switching the cordless headphones

on/off

Press button

Depending on the previous status, the

headphones are switched on or off. To save

the battery, the headphones are switched

off automatically if they do not receive an

audio signal within three minutes.

Adjusting the volume of the

headphones

Turn volume control

until the desired

volume has been set.

If you have connected corded

headphones to a rear-compartment

screen, you can adjust the volume by

pressing buttons

on the remote control

(

page 24).

Selecting a screen for the headphones

Move push slider

;

to L (left-hand screen)

or R (right-hand screen).

Indicator lamp displays

The color of the indicator lamp shows

whether the headphones are switched on or

off and indicates the charge level of the

batteries inserted.

174

General information

Rea

rEnt

tai

nme

ste

Summary of Contents for Comand MY11



































































































































































































Search results

Summary of Contents for Comand MY11

Reviews:

Related manuals for Comand MY11

Brands by name

Popular brands

Mercedes-Benz Comand MY11, Operating Instructions Manual

Search results

Summary of Contents for Comand MY11

Reviews:

Related manuals for Comand MY11

Brands by name

Popular brands