Mercedes-Benz Comand MY11 Page 171 Operating Instructions Manual Download

Page: 171 / 194

Showing/hiding the menu

To show: press

the COMAND

controller.

To hide: slide

the COMAND controller

and confirm

Full Screen

by pressing

Volume and sound settings

You will find details on volume (

page 35)

and sound (

page 35) settings in the "At a

glance" section.

WARNING

External video sources may have different

volumes, which can mean that system

messages such as traffic announcements and

navigation system announcements are much

louder. If necessary, please deactivate the

system messages or adjust their volume

manually.

It may be the case that a device which is

connected as an external video source

seems quieter or louder in the vehicle, or

that the usual maximum volume cannot be

reached. On some devices, it is possible to

adjust the volume separately. In this case,

start at a medium volume and increase it

gradually. This enables you to determine

whether the system is able to play the

sound at high volume without distorting it.

Increasing the volume using COMAND

Select

Volume

in the AUX display by turning

cVd

the COMAND controller and press

to confirm.

A menu appears. The

dot indicates the

current setting.

Select

Standard

Boost

and press

confirm.

Standard

: the volume of the external video

source is adjusted to a standard value.

Boost

: the volume of the external video

source is raised by approximately 10 dB.

Video AUX mode

169

Video

Summary of Contents for Comand MY11



































































































































































































Search results

Summary of Contents for Comand MY11

Reviews:

Related manuals for Comand MY11

Brands by name

Popular brands

Mercedes-Benz Comand MY11, Operating Instructions Manual

Search results

Summary of Contents for Comand MY11

Reviews:

Related manuals for Comand MY11

Brands by name

Popular brands