McLaren coupe series Owner'S Handbook Manual Download Page 224 | Manualshive

Page: 224 / 272

background image

Maintaining Your McLaren

Wheels and Tires

5.32

Wheels and Tires

Wheels and tires

WARNING: Have worn tires replaced
in axle pairs and ensure the tires are
fitted as specified. With worn tires,
the driving stability of the vehicle
will be adversely affected,
especially when driving at high
speeds.

Consult your McLaren retailer if you
have had new tires fitted for
information on the appropriate
bedding in time based on your
driving style.

•

With new tires, avoid high speed
cornering and excess speed.

•

Only have wheels and tires of the
same type and make fitted.

•

Never use a tire which has been
punctured and then repaired.

•

Only have tires of the correct size
fitted.

•

Tires degrade over time due to the
effects of ultraviolet light, extreme
temperatures, high loads, and
environmental conditions. It is

recommended that tires are
replaced every 6 years, or sooner if
required.

McLaren recommends that you only use
Pirelli summer or winter tires, See Wheel and
tire sizes, page 6.13.

These tires provide the best possible
performance in conjunction with the safety
systems on your vehicle and have been
specifically approved by McLaren.

McLaren cannot accept any responsibility for
damage that may result from use of other
tires and wheels. Further information about
wheels and tires can be obtained from your
McLaren Retailer.

WARNING: Using tires other than
those which have been
recommended by McLaren, may
contact the body work and
adversely affect the handling. This
may cause loss of vehicle control,
resulting in serious personal injury
or death. Noise levels and fuel
consumption may also be adversely
affected. In addition, when driving
with a load or when using snow
traction devices, they could cause

contact between the bodywork and
axle components. This could result
in damage to the tires or the vehicle.

NOTE: Retreaded tires must not be
used. Do not fit used tires if you have
no information about their previous
usage.

NOTE: Modification to the brake
system and wheels is not permitted,
nor is the use of spacer plates or brake
dust shields. Any such modifications
will invalidate the vehicle warranty on
the area modified.

NOTE: A wheel change must be carried
out at your McLaren retailer. The
vehicle could be damaged if it is jacked
up incorrectly

NOTE: Store tires in a cool, dry place,
preferably in the dark. Protect the tires
from oil, grease and petrol.

p13.book Page 32 Wednesday, April 26, 2017 9:22 PM

«
...
222
223
224
225
226
...
»

Summary of Contents for coupe series

















































































































































































































































































Reviews:

No comments

Related manuals for coupe series

Brand: Camcar Pages: 6

Brand: ABL Pages: 4

Brand: Ford Pages: 368

Brand: Mazda Pages: 122

Brand: H&S Pages: 32

1966 Spider 105

Brand: Alfa Romeo Pages: 46

Brand: PEUGEOT Pages: 17

Brand: TEINHOF Pages: 2

2000 9-5 2.3 Turbo Ecopower

Brand: Saab Pages: 256

Prime Design OCM-3032

Brand: Safe Fleet Pages: 4

Brand: PEUGEOT Pages: 232

Brand: Ford Pages: 8

Sebring Convertible

Brand: Chrysler Pages: 454

Brand: Beeper Pages: 2

Brand: A-Tach Mounts Pages: 2

Brand: Thule Pages: 1

Brand: Datsun Pages: 104

Brand: Saab Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands