masosine SPS 100 User Manual Download Page 86

Page: 86 / 139

Removing the static flushing device—SPS 200, SPS 300 and SPS 400
pumps with cast iron power frame

Note

: The flushing device (if fitted) must be emptied and removed before dismantling the pump.

•

Use a 19mm spanner to loosen the retaining nut holding the bent outlet in position (arrowed)

enough to allow the bent outlet to be lowered into a horizontal position.

•

Hold a vessel under the bent outlet. Drain until no more liquid runs out of the power frame.

•

Remove the retaining nut holding the sight glass and its connection pieces in position and remove
the sight glass and its connection pieces. Remove the bent outlet in the same way.

Fitting a flush ring without flush connections—SPS 200, SPS 250, SPS 300,
SPS 400 and SPS 500 pumps with stainless steel power frame

The SPS 300 is shown here. Flushing options for the SPS 200, SPS 250, SPS 400 and the SPS 500 are
similar.

m-SPS-en-08

Summary of Contents for SPS 100












































































































































Search results

Summary of Contents for SPS 100

Reviews:

Brands by name

Popular brands

masosine SPS 100, User Manual

Search results

Summary of Contents for SPS 100

Reviews:

Brands by name

Popular brands