manualshive.com logo in svg

masosine SPS 100, User Manual

Share
Download
masosine SPS 100 User Manual Download Page 85

Removing the static flushing device—SPS 100 pumps

Note

: The flushing device (if fitted) must be emptied and removed before dismantling the pump.

•

To remove the static flushing device, pour the flushing fluid from the sight glass, and reverse the

sequence of operations described above.

23.2 SPS 200, SPS 300, SPS 400 and SPS 500

Fitting the static flushing device—SPS 200, SPS 300 and SPS 400 pumps
with cast iron power frame

The static flushing device for the SPS 300 is shown here. The static flushing devices for the SPS 200 and
the SPS 400 are similar.

•

Use a 6mm Allen key to remove the two nipples (arrowed) (if fitted) from the pump’s power frame.

•

Fit the sight glass connection piece in place of the top nipple. Use a 19mm spanner to tighten it. Fit
the sight glass and tighten the retaining nut to hold it in position.

•

Fit the bent outlet in place of the bottom nipple in the same way.

•

Fill the system with flushing fluid to the level of the top bend of the bent outlet.

m-SPS-en-08

85

Summary of Contents for SPS 100












































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands