manualshive.com logo in svg

masosine SPS 100, User Manual

Share
Download
masosine SPS 100 User Manual Download Page 74

•

Guide the optional special cylindrical tool (arrowed: TL-SP21-002-50, TL-SP25-002-50, TL-SP40-

002-50 or TL-SP50-002-50 - available to order) over the shaft and push it home. This will give
some protection to the shaft splines as the pump housing is removed. It is important not to
damage the shaft while removing or installing the pump housing.

•

Use a 17mm spanner to loosen and remove the two screws

(right-hand thread)

and washers

which secure the pump housing to the power frame.

•

If necessary, gently tap the pump housing with a soft hammer to free it. Withdraw the pump

housing carefully.

The pump housing is heavy.

Removing the seal and the static face—pumps with a single mechanical seal

•

Push the mechanical seal from the rear of the pump housing and remove it.

Note

: The mechanical

seal is a tight push fit.

•

Remove the static face from the mechanical seal.

•

You can now access the seal housing O-ring in its groove in the pump housing (arrowed), and the
O-ring in the mechanical seal (arrowed).

The static face

Pump housing O-ring

The mechanical seal

Removing the seal—pumps with a single mechanical seal

•

A graphic making clear how to disassemble and assemble the seal appears in "Seals" on page 119.

Pumps with a triple lip seal

See the graphics in "Seals" on page 119 and "Front support versions" on page 129 , and refer to the
instructions for the SPS 200 pump triple lip seal disassembly in section "Removing the rear liner—SPS 200
pumps with a triple lip seal" on page 55. The SPS 250, SPS 300, SPS 400 and SPS 500 are similar.

74

m-SPS-en-08

Summary of Contents for SPS 100












































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands