manualshive.com logo in svg

masosine SPS 100, User Manual

Share
Download
masosine SPS 100 User Manual Download Page 80

Fitting the front support, the shaft nut and locking screw

The shaft nut

The PEEK front support

The shaft locking screw

It is important to ensure that the shaft cannot rotate while the shaft locking screw and the shaft nut are
tightened. It may be convenient to secure it using a well-padded wrench on the shaft and the key or
keyway. A blocking tool for the shaft is optionally available for easy opening of the locking screw (SPS
250: TL-SP21-010-31, SPS 300: TL-SP25-010-31, SPS 400: TL-SP40-010-31 and SPS 500: TL-SP50-010-31).

•

Check that the shaft nut O-ring (arrowed) is in position on the shaft nut.

•

Fit the shaft nut into the front support.

•

Fit the shaft nut and front support over the shaft.

•

Use the ring spanner to tighten it (right-hand thread) to 65Nm (SPS 250); 110Nm (SPS 300);

125Nm (SPS 400); 125Nm (SPS 500).

•

Fit the shaft locking screw (left-hand thread) to the shaft. Use the ring spanner to tighten it to

45Nm (SPS 250); 95Nm (SPS 300); 105Nm (SPS 400); 105Nm (SPS 500).

80

m-SPS-en-08

Summary of Contents for SPS 100












































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands