manualshive.com logo in svg

masosine SPS 100, User Manual

Share
Download
masosine SPS 100 User Manual Download Page 25

The gate and gate guide shown inverted to make clear
the gate’s position within the guide for counter-
clockwise rotor rotation

The gate and gate guide oriented for counter-clockwise
rotor rotation

The gate and gate guide oriented for clockwise rotor
rotation

If the direction of rotation is reversed, change the rotation direction indicator arrows and mark the
suction and pressure ports correspondingly.

Disconnect the pump from the mains power, and secure it against unintentional
start-up. Ensure that the direction change is carried out by a trained engineer.

•

Follow the dismantling and assembly steps for your pump model. See "Disassembly and assembly"
on page 38

•

Take special note of the instructions for fitting the rotor, the gate and the gate guide

Take care that fluid in the pressure line leaves the pump in an upward direction, so that when pumping
stops, some fluid remains in the pump. This will make it easier for the pump to draw in viscous products
when pumping restarts. This applies particularly when the pressure connection is horizontal: positions
12-3 and 12-9. Take care that the pressure line is run so that the pump rotor is always covered with fluid,
and dry running is avoided.

m-SPS-en-08

25

Summary of Contents for SPS 100












































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands