manualshive.com logo in svg

masosine SPS 100, User Manual

Share
Download
masosine SPS 100 User Manual Download Page 67

Fitting the shaft nut—SPS 200 pumps

The shaft nut

It is important to ensure that the shaft cannot rotate while the shaft nut is fitted. It may conveniently be
secured using a tommy bar or a spanner handle between the spider castellations on the drive shaft.
Alternatively, a well-padded wrench can be used on the shaft and the key or keyway. A blocking tool for
the shaft is optionally available for easy opening of the locking screw (SPS 200: TL-SP20-010-31).

•

Check that the shaft nut O-ring (arrowed) is in position on the shaft nut.

•

Fit the shaft nut (right-hand thread) over the shaft. Use a 32mm ring spanner to tighten it to 65Nm.

Fitting the shaft locking screw

The shaft locking screw

It is important to ensure that the shaft cannot rotate while the shaft locking screw is fitted. It may
conveniently be secured using a tommy bar or a spanner handle between the spider castellations on the
drive shaft. Alternatively, a well-padded wrench can be used on the shaft and the key or keyway.

•

Fit the shaft locking screw (left-hand thread) to the shaft. Use a 32mm ring to tighten it to 45Nm.

Fitting the front liner

•

Push the front liner into position, pushing evenly at both ends so that it does not jam. The anti-

rotation pins within the pump housing (arrowed) guarantee that the liner is properly positioned.
The two liners are identical.

m-SPS-en-08

67

Summary of Contents for SPS 100












































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands