manualshive.com logo in svg

masosine SPS 100, User Manual

Share
Download
masosine SPS 100 User Manual Download Page 44

•

Position the static face in the mechanical seal, with the static face’s O-ring facing the mechanical

seal. The static face has two recesses (arrowed) which must be correctly aligned with lugs
(arrowed) either side of its seat

•

Use a finger to retain the static face in position on the mechanical seal and push them on to the

pump shaft and all the way home into the pump housing.

Note

: The mechanical seal has a lug on

its inner surface which must be aligned with the shaft splines.

SPS 100 pumps with a triple lip seal: fitting the distance piece

•

Check that the distance piece O-ring is in position.

•

Push the distance piece into position, flanged end first.

Pumps with a triple lip seal: fitting the back bushing

•

Push the back bushing into position, thick end (arrowed) towards the front. (The two bushings are
identical.)

44

m-SPS-en-08

Summary of Contents for SPS 100












































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands