manualshive.com logo in svg

masosine SPS 100, User Manual

Share
Download
masosine SPS 100 User Manual Download Page 35

•

If this dimension is not correct, continue disassembly (see "Disassembly and assembly" on

page 38) until the face of the power frame is accessible (the SPS 300 and the SPS 200 pumps are
shown here; the SPS 400 is similar).

•

Use a 6mm Allen key to loosen and remove the bearing housing retaining screws and copper

washers (arrowed; the number of screws varies with pump model.)

•

Remove the bearing housing and the pump shaft, being careful not to damage the lip seals

(arrowed). Note: lubricating oil will spill out as the bearing housing is removed.

•

Remove the shim ring (arrowed in the three lower pictures) and install a new one. Reassamble,

tightening the bearing housing retaining screws to 25Nm (SPS 200) 50Nm (SPS 300) 35Nm (SPS
400), and measure dimension X again.

•

If this dimension is not correct, disassemble and peel layers from the shim ring equal in total

thickness to the difference between the-re-measured distance and the correct distance, so that the
correct dimension X is achieved. One layer is 0.05mm thick.

•

Reassemble.

m-SPS-en-08

35

Summary of Contents for SPS 100












































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands