manualshive.com logo in svg

masosine SPS 100, User Manual

Share
Download
masosine SPS 100 User Manual Download Page 31

19

Changing the oil

19.1 SPS 100

Every day before using your pump, check that there is enough grease in the storage chamber. Remove
the vent at

A

and insert grease through the nipple at

B

until grease starts to come out at

A

. Refit the

vent.

Standard first filling, for -10 to 60°C (14 to 140°F): MOLYDUVAL Soraja C532, DIN 51502.

Grease grades for Ex zones:

•

At temperature class T4 (60°C (140°F) or less: MOLYDUVAL Soraja C532, DIN 51502.

•

At temperature class T3 (61 to 120°C (142 to 248°F) or less: MOLYDUVAL Pegasus KD 460.

C

A

B

19.2 SPS 200, SPS 250, SPS 300, SPS 400, SPS 500

Every day before using your pump, check the oil viewing glass at B (see 27 in the parts list,"Parts lists"
on page 91) in the bearing housing (see 11 in the parts list, "Pumps" on page 92) for damage and to
confirm that enough oil is in the power frame. The oil should reach the middle of the glass.

•

Check that the drain plug

C

is in place and fully tightened.

•

Open port

A

and fill the power frame with suitable oil (see Note, below) until it is nearly full.

•

Close port

A

.

•

Check the oil level in viewing glass at

B

. Do not allow the level to fall below the viewing glass

centre line.

Note

: If the pump is intended to be used in an area where ATEX regulations apply, the oil viewing glass is

replaced by a screwed plug.

Note

: When a new pump is supplied, it is filled as standard with Klüberoil 4 UH 1-220 N lubrication oil for

the food and pharmaceutical industries, which is suitable for process temperatures between –30C (-22F)
and 120C (248F).

If the pump is intended to be used in an area where ATEX regulations apply, only

this oil must be used.

Filling volumes

SPS 200

SPS 250

SPS 300

SPS 400

SPS 500

Cast iron power frame

Approx 0.10

litre

N/A

Approx 0.18

litre

Approx 0.38

litre

N/A

Stainless steel power
frame

Approx 0.10

litre

Approx 0.10

litre

Approx 0.18

litre

Approx 0.35

litre

Approx 0.45

litre

Dispose of used oil according to local regulations.

Oil or grease needs to be changed at least once a year.

m-SPS-en-08

31

Summary of Contents for SPS 100












































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands