manualshive.com logo in svg

masosine SPS 100, User Manual

Share
Download
masosine SPS 100 User Manual Download Page 70

Removing the shaft locking screw and the shaft nut

It is important to ensure that the shaft cannot rotate while the shaft locking screw and the shaft nut are
removed. It may be convenient to secure it using a well-padded wrench on the shaft and the key or
keyway. A blocking tool for the shaft is optionally available for easy opening of the locking screw SPS
250: TL-SP21-010-31, SPS 300: TL-SP25-010-31, SPS 400: TL-SP40-010-31 and SPS 500: TL-SP50-010-31)

•

Use ring spanner to remove the locking screw from the shaft

(left-hand thread)

.

•

Use ring spanner to remove the shaft nut from the shaft

(right-hand thread)

. It will leave the

shaft with the front support.

•

You can now access the rotor front O-ring (arrowed) in its groove in the rotor front.

•

Remove the shaft nut from the PEEK front support.

Note

: the PEEK front support is breakable.

•

You can now access the shaft nut O-ring (arrowed) in its groove in the shaft nut.

70

m-SPS-en-08

Summary of Contents for SPS 100












































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands