manualshive.com logo in svg

masosine SPS 100, User Manual

Share
Download
masosine SPS 100 User Manual Download Page 64

Fitting the sealing system—SPS 200 pumps with a cast iron power frame and a triple lip seal

seal housing

shaft sleeve

lip seals

•

Push the seal housing into the shaft sleeve.

•

Push the shaft sleeve fitted with the seal housing over the shaft and into position, the chamfered,
lip-seal end of the shaft sleeve first. The shaft sleeve is a tight push fit. Be sure to push it all the
way home. The shaft sleeve has an alignment lug inside it which must be aligned with the shaft
splines.

Fitting the rear liner—SPS 200 pumps with a triple lip seal

•

Push the rear liner into position below the shaft sleeve, pushing evenly at both ends so that it does
not jam. The anti-rotation pins within the pump housing (arrowed) guarantee that the liner is
properly positioned. The two liners are identical.

Fitting the sealing system—SPS 200 pumps with a stainless steel seal housing for a triple lip seal

seal housing

shaft sleeve

lip seals

•

Push the shaft sleeve into the seal housing (with the lip seals)

64

m-SPS-en-08

Summary of Contents for SPS 100












































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands