masosine SPS 100 User Manual Download Page 45

Page: 45 / 139

Fitting the rear liner—all SPS 100 pumps

•

Push the rear liner into position, pushing evenly at both ends so that it does not jam. The anti-

rotation pins within the pump housing (arrowed) guarantee that the liner is properly positioned.
The two liners are identical.

Fitting the rotor, the gate and the gate guide

This end

in first

Note gate

orientation

within the

guide

The gate and gate guide inverted to show the
gate’s position within the guide for counter-
clockwise rotor rotation

The rotor

The gate and

gate guide oriented for

clockwise rotor rotation

The gate and gate guide

oriented for counter- clockwise

rotor rotation

Pressure

side

Suction

side

Suction

side

Pressure

side

•

Check that the rotor O-ring is in position.

•

Position the gate within the gate guide and hold as one unit.

Check that the gate and gate guide are correctly oriented for the desired sense of
rotor rotation. This is critical for proper operation.

m-SPS-en-08

Summary of Contents for SPS 100












































































































































Search results

Summary of Contents for SPS 100

Reviews:

Brands by name

Popular brands

masosine SPS 100, User Manual

Search results

Summary of Contents for SPS 100

Reviews:

Brands by name

Popular brands