manualshive.com logo in svg

Mallinckrodt INOMAX DSir Plus, Operation Manual

Share
Download
Mallinckrodt INOMAX DSir Plus Operation Manual Download Page 50

Part No. 20717  Rev-01

2014-07

2-10

2. At the back of the INOmax DS

IR

, remove 

the regulator hose from the INOMAX gas 

inlet and connect it to the purge port.

  This depressurizes the regulator.

Depressurizing the Regulator Supply Line

Depressurizing the regulator supply line removes the buildup of NO

2

 and allows the use of the INOmax DS

IR

®

 

at any time within the next 12 hours. If the regulator supply line is not depressurized, the INOmax DS

IR

 must 

be used within 10 minutes after completing pre-use checkout procedure.

To depressurize the INOMAX regulator supply line: 

3. When the regulator pressure gauge reads zero, 

remove the regulator hose from the purge port 

and connect it to the INOMAX gas inlet.

Note:

If difficulties are encountered in 

connecting the regulator hose, 

refer to page 7-9.

1. On the INOMAX cylinder, rotate the INOMAX 

cylinder handle clockwise to close the valve.

Summary of Contents for INOMAX DSir Plus















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands