manualshive.com logo in svg

Mallinckrodt INOMAX DSir Plus, Operation Manual

Share
Download
Mallinckrodt INOMAX DSir Plus Operation Manual Download Page 199

Part No. 20717  Rev-01

2014-07

9-3

3. Connect the INOmax DS

IR

 power cord to an 

emergency-power-backed hospital-grade 

outlet. The power cord must always be  

 

connected to an electrical outlet to maintain  

a full battery charge.

  Verify the main power supply indicator light 

is illuminated (green). This indicates that the 

power cord is plugged into an electrical outlet.

3

Caution:

Keep the power cord off of the 

ground and away from moving 

parts.

4. Load two INOMAX drug cylinders onto 

cart and check for correct product identity 

labels, cylinder concentration (800 ppm) and 

expiration date.

5. Connect an INOMAX regulator to one of the 

INOMAX cylinders, and hand tighten the fitting 

to the INOMAX cylinder. Connect the INOMAX 

regulator hose to one of the INOMAX inlets 

(see page 7-9 for additional instructions).

Caution:

If using the transport regulator/cap 

assembly (PN 10022) see Figure 

4-7, Section 4/ Transport.

Note: For the CGA-type INOMAX regulator 

connector, ensure the white plastic tip 

is not chipped or cracked. Remove and 

replace as necessary. (see Replacing the 

tip on the INOMAX regulator, Page 7-8).

Summary of Contents for INOMAX DSir Plus















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands