Mallinckrodt INOMAX DSir Plus Operation Manual Download Page 41

Page: 41 / 206

Part No. 20717 Rev-01

2014-07

2-1

2/ Automated Pre-Use Checkout

An INOmax DS

splash screen will appear once

the device is turned ON followed by a Mallinckrodt

test screen (confirm that the speaker sounds).

• Pressing the NEXT button initiates the Pre-Use

wizard.

• Pressing the CANCEL button exits the Pre-Use

wizard. If you cancel out of the pre-use wizard,

the manual pre-use checkout procedure can be

found in Section 9/Appendix.

Note: • Low calibration automatically starts

following the INOmax DS

self test.

• A Pre-Use wizard will be displayed on

the main screen, which will provide

step-by-step instructions to complete

the pre-use procedure.

Self Test Screen

Turn ON INOmax DS

Note:

Following unpacking and prior to the first use:

• Remove any protective caps from the connectors and ports on the INOmax DS

• Ensure the INOmax DS

is on a flat surface or is fixed securely to a cart or transport sled.

Connect the INOmax DS

power cord to an emergency-power-backed hospital-grade outlet. The power

cord must always be connected to an electrical outlet to maintain a full battery charge.

Summary of Contents for INOMAX DSir Plus















































































































































































































Search results

Summary of Contents for INOMAX DSir Plus

Reviews:

Brands by name

Popular brands

Mallinckrodt INOMAX DSir Plus, Operation Manual

Search results

Summary of Contents for INOMAX DSir Plus

Reviews:

Brands by name

Popular brands