manualshive.com logo in svg

Mallinckrodt INOMAX DSir Plus, Operation Manual

Share
Download
Mallinckrodt INOMAX DSir Plus Operation Manual Download Page 23

Part No. 20717  Rev-01

2014-07

1-11

Main Screen

When an INOMAX cylinder valve is opened, the 

cylinder handle graphic will turn green representing 

an open INOMAX cylinder valve.

The cylinder icons will appear on the main screen in 

relation to their position on the cart when the user is 

facing the INOmax DS

IR

. 

Cylinder icons are not visible and the NO delivery 

setpoint button will remain inactive until the 

INOmax DS

IR

 recognizes an INOMAX cylinder.

Caution:

High frequency and/or high intensity light 

emission, in the area of the INOmeter, may 

interfere with communication between the 

INOmax DS

IR

 and the INOmeter on the 

INOMAX cylinder (see page 1-15).

Note: When using the transport regulator/cap 

assembly (PN 10022) only one cylinder 

will be displayed.

Summary of Contents for INOMAX DSir Plus















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands