M A G U I R E P R O D U C T S , I N C .
24
W E I G H S C A L E B L E N D E R
Display will show
COMPONENT 1: ON
Press "1" repeatedly to observe operation.
PRESS
Device number 2 will operate.
Display will show
COMPONENT 2: ON
Press "2" repeatedly to observe operation.
REPEAT THIS SEQUENCE
For each dispense valve on your WEIGH SCALE BLENDER.
Up to 12 outputs are possible numbered 1 through to 9, A, B, and C.
Only those connected to devices will operate.
3. NOTE HOPPER NUMBERS
AT THIS POINT
NOTE which component NUMBER is assigned to each hopper.
You will want to know each hopper's correct component number.
FOR WSB 940 & WSB
1840 SERIES:
On 9000 and 18000 gram, FOUR hopper compartment systems, facing the
Controller side of the blender:
Device 1 is the NEAR hopper, 2 the FAR hopper, 3 the LEFT CENTER, and 4 the
RIGHT CENTER hopper.
FOR WSB 100, 200 &
400 SERIES:
On 1000, 2000, and 4000 gram, FOUR hopper systems facing the Controller side of
the blender:
Devices 1, 2, 3, and 4 are counter-clockwise starting with far left corner hopper.
FOR WSB 200, 400, 900
& 1800 SERIES:
On 2000, 4000, 9000 and 18000 gram SIX hopper systems facing the Controller side
of the blender:
Devices 1, 2, 3, 4, 7, and 8 are counter-clockwise starting with far left corner hopper.
FOR WSB 100, 200,
400, 900 & 1800
SERIES:
On the blender Controller:
Device 5 is the LEFT Panel-front OUTLET.
Device 6 is the RIGHT Panel-front OUTLET.
4. OPERATE OTHER DEVICES
PRESS
The weigh bin air solenoid will operate. Display will show
DUMP: ON
The weigh bin dump valve will open.
Press, "DUMP" repeatedly to observe operation.
PRESS
This key controls the mix motor outlet on the side of the controller.
The mixer motor will run. Display will show
MIXER: ON
Mix blade turns clockwise facing the motor shaft or 270º on Pneumatic Mix Motors.
Mixer switch must be down; timed position.
PRESS
The Flow Control Valve will operate. Display will show
HOLD: ON
(Under the mix chamber - this device is optional)
PRESS
The Strobe light and Beeper will operate.
Display will show
ALARM: ON
PRESS
Press twice, to return to normal mode.
Verify normal mode by observing that the display shows
WAITING
in lower right.
Summary of Contents for WEIGH SCALE BLENDER WSBMB Series
