Maguire Products WEIGH SCALE BLENDER WSBMB Series, Installation Operation & Maintenance

Page: 60 / 148

M A G U I R E P R O D U C T S , I N C .
60
W E I G H S C A L E B L E N D E R

When proper selection is displayed, move on to NEXT component by pressing the * key.
REPEAT the "* CE" sequence for ALL components you use.
The * key will walk you through all components, 1 through 9, then A, B, C (A=10, B=11, C=12).
The CE key will change the TYPE for a component.
Components NOT CONNECTED, or NEVER USED, set to OFF.
EXIT will exit the sequence at any time.
After EXIT, if display says
NEED NATURAL then you have specified an ADDITIVE without specifying a
NATURAL. This is an unacceptable condition.
FOUR dispense valve systems use components 1 to 4.
TWO dispense valve systems use 1 and 2.
SIX dispense valve systems use 1 to 4, then 7 and 8.
Panel front OUTLETS are always components 5 and 6.
DISPLAY Firmware Status and Checksum
Press (*,
2 , 5 ) to display the Firmware status and checksum. (Previously: Check the ROM-CHECK Flag).
Displays the firmware status and checksum. When finished, press Exit , and then press Exit again to exit
out of Program Mode.
USB Recipe Command
Press (*, 3 , 4 ) to enable or disable the USB Recipe Command. Use the * key to toggle USB Recipe
Command enable or disable. Enabling the USB Recipe Command enables the following options:
The Recipe key (RECP) allows the user to save the current recipe to USB (press RECP once), press * to
save. Note: The Recipe key (RECP) is only enabled in Program Mode.
The Recipe key (RECP) allows the user to view the current recipe file stored on the USB key (press RECP
twice), press * to view.
With the USB Recipe Command enabled, the blender will look for a USB drive plugged into the USB port
on the controller that contains a file named “RECP_CMD.TXT” located within a folder named “maguire”. If
that file exists and is formatted correctly, the controller will run the recipe stored on the USB drive. If the
USB drive does not exist, the RECP_CMD.TXT files does not exist or the RECP_CMD.TXT is not
formatted correctly, the controller will stop and alarm.
Example USB Recipe Description
T
S1:1:100:000:00004:
S2:2:500:000:00004:
S3:2:500:000:00004:
S4:3:030:000:00004:
S5:3:030:000:00004:
S6:0:000:000:00004:
S7:0:000:000:00004:
S8:0:000:000:00004:
S9:0:000:000:00004:
SA:0:000:000:00004:
SB:0:000:000:00004:
SC:0:000:000:00004:
E T = 12 software, W = 4 Software
Column 1: S1 through SC = components 1 through 12
Column 2: 1 = Regrind, 2 = Natural, 3 = Additive (additive is the same as color)
Column 3: Setting value. Implied decimal in 10ths for regrind and additive.
Column 4: XT Parameter (See XT Parameter on page 85)
Column 5: Alarm parameter (See AT parameter alarm on page 84)
E = End of file
END CYCLE WITH: BIN EMPTY, BIN FULL
This flag for SPECIAL APPLICATIONS ONLY.
Press (*,4,4) to tell the controller to end a cycle when the weigh bin is FULL. Use the * key to toggle
between
BIN EMPTY or BIN FULL .
Normal operation is to end the cycle BIN EMPTY. The BIN FULL option is only for special installations
where the sensor has been relocated BELOW the mix chamber and the instructions to do otherwise.
SET MANUAL MODE PASSWORD
Press (*,4,5, followed by a 5 digit number) to change the PASSWORD number for entering the MANUAL