IMPULSE•G+ Mini Advanced Instruction Manual – March 2014
5-14
Acceleration/Deceleration
Acceleration time sets the time necessary for the output frequency to accelerate from 0Hz to
maximum output frequency (E01.04). Deceleration time sets the time necessary for the output
frequency to decelerate from the maximum output frequency (E01.04) to 0Hz.
Parameter
Code
Name
Function
Range
Initial Value
Access
Level
B05.01
Accel Time 1
Sets acceleration time.
0.0–25.5 sec
5.0*
Basic/Adv
B05.02
Decel Time 1
Sets deceleration time.
0.0–25.5 sec
3.0*
Basic/Adv
B05.03
Accel Time 2
Sets alternate accel time.
Enabled by multi-function input=1A.
0.0–6000.0 sec
2.0
Basic/Adv
B05.04
Decel Time 2
Sets alternate decel time.
Enabled by multi-function input=1A.
0.0–6000.0 sec
2.0
Basic/Adv
B05.05
Accel Time N Change
Sets acceleration time at Speed Switch
frequency.
0.0–25.5 sec
2.0
Adv
B05.06
Decel Time N Change
Sets deceleration time at Speed
Switch frequency.
0.0–25.5 sec
2.0
Adv
B05.08
Fault Stop Time
Sets deceleration time for complete
stop at external fault. See External
Response Selection page 5-51.
0.0–25.5 sec
1.0
Adv
B05.09
Accel/Decel Units
Determines acceleration/deceleration
switching level
00, 01
01
Adv
00 0.01 sec for 0.00-
2.55 sec
NOTE:
Setting will not change if
any accel/decel time is >
2.55 sec.
01 0.1 sec for 0.0-25.5
sec
B05.10
Accel/Decel Switch
Frequency
Determines acceleration/deceleration
switching level
0.0–150.0 Hz
120
Adv
B05.11
Switch Frequency
Determines when Acceleration Time
and Deceleration Time at Speed
Switch Hz is enabled
0.0–6000.0
01
Adv
00 lower SW freq
B05.05/06 is enabled, N-out
B5.10
01 upper SW freq
B05.06 is enabled, N-out
B5.10
B05.12
Accel Time 3
Acceleration time when H01.01 to
H01.07 = 1B
0.0–6000.0
3.0
Adv
B05.13
Decel Time 3
Deceleration time when H01.01 to
H01.07 = 1B
0.0–6000.0
3.0
Adv
B05.14
Accel Time 4
Acceleration time when H01.01 to
H01.07 = 1C
0.0–6000.0
3.0
Adv
B05.15
Decel Time 4
Deceleration time when H01.01 to
H01.07 = 1C
0.0–6000.0
3.0
Adv
* Initial value is determined by X-Press Programming (Table 4.1 to 4.2).
Summary of Contents for 2001-G+M
