![background image](http://html1.mh-extra.com/html/magnetek/2001-g-m/2001-g-m_instruction-manual_3598661178.webp)
IMPULSE•G+ Mini Advanced Instruction Manual – March 2014
A-14
114: (Inverse) Freq Set 2
115: (Inverse) Frequency Detect 3
117: (Inverse) Torque Detect 1 N.C.
118: (Inverse) Torque Detect 2 N.O.
119: (Inverse) Torque Detect 2 N.C.
11A: (Inverse) Forward Direction
11B: (Inverse) Reverse Direction
11C: (Inverse) Swift-Lift Active
11D: (Inverse) Base Block N.C.
120: (Inverse) Auto-Reset
121: (Inverse) Overload OL1
122: (Inverse) Overheat Pre-Alarm
123: (Inverse) Torque Limit
126: (Inverse) Run Command is input
127: (Inverse) Load Check Detect
129: (Inverse) Upper Limit
12A: (Inverse) During Run 1
12B: (Inverse) During Fast Stop
12F: (Inverse) Load Weakening
130: (Inverse) Lower Limit
131: (Inverse) Upper/Lower Limit
135: (Inverse) Load Check Fault
Detection
137: (Inverse) Maintenance
139: (Inverse) Drive Enable
13A: (Inverse) Overheat Pre-Alarm Time
Limit
13D: (Inverse) During Speed Search
13F: (Inverse) Klixon
140~1FF: (Inverse) Fault Annunciate
H02.02
Output Terminal P1 Select
(See H02.01 for selections)
00F*
000–1FF
--
5-51
H02.03
Output Terminal P2 Select
(See H02.01 for selections)
00F*
000–1FF
--
5-51
H03.01
Terminal A1 Signal Select
00: 10 VDC
00*
00
--
5-55
H03.02
Terminal A1 Select
00: Frequency Bias
01: Frequency Gain
02: Aux Speed Reference 1
03: Aux Speed Reference 2
04: Output Voltage Bias
07: OT/UT Detection Level
0F: Not Used
10: Forward Torque Limit
11: Reverse Torque Limit
12: Regen Torque Limit
15: FWD/REV Torque Limit
1F: Not Used
00
00–1F
--
5-55
H03.03
Terminal A1 Gain
100.0
-999.9–999.9
%
5-55
H03.04
Terminal A1 Bias
0.0
-999.9–999.9
%
5-55
H03.09
Terminal A2 Signal Select
00: 0~10 VDC
02: 4 to 20 mA
03: 0 to 20 mA
02
00, 02, 03
--
5-56
Parameter Parameter Name
Default
Range
Units
Reference
Page
* Parameters defaults changed by X-Press Programming
** Parameters changed by E01.03
*** Value depends on drive model
**** Default value depends on control method
Summary of Contents for 2001-G+M
