IMPULSE•G+ Mini Advanced Instruction Manual – March 2014
A-19
L08.06
Input Phase Loss Detection Level
(Increasing L08.06 from default value
may cause DC BUS capacitor failure)
5.0
0.0–5.0
%
5-75
L08.07
Output Phase Loss Selection
00: Disabled
01: Enabled
01
00, 01
--
5-75
L08.08
Output Phase Loss Detection Level
5.0
0.0–20.0
%
5-75
L08.09
Ground Fault
00: Disable
01: Enable
01***
00, 01
--
5-75
L08.10
Fan Operation Selection
00: Fan On - Run with Time (L08.11)
01: Fan Always On
00
00, 01
--
5-75
L08.11
Fan Off-Delay Time
60
0–300
sec
5-75
L08.12
Ambient Temp
40
-10–50
°C
5-75
L08.15
OL2 Sel @ Low Speed
00: Disabled
01: Enabled
01
00, 01
--
5-75
L08.18
Soft CLA Sel
00: Disabled
01: Enabled
01
00, 01
--
5-76
L08.19
Overheat Pre-Alarm Frequency Reduction
Rate
0.8
0.1, 0.9
%
5-76
L08.35
Mounting Selection
00: Disabled (standard installation)
01: Side-By-Side
02: NEMA 1 Standard
03: Finless
00
00–03
--
5-76
L08.41
High Current Alarm Selection
00: Disable
01: Enable
00
00, 01
--
5-76
L09.01
Auto Reset Select
00: Disable
01: Enable
01
00, 01
--
5-77
L09.02
Auto Reset Attempts
03
00–10
--
5-77
L09.03
Auto Reset Time
0.5
0.5–180.0
sec
5-77
L09.04
Auto Reset Fault Select 1
0001
0000–FFFF
--
5-77
L09.05
Auto Reset Fault Select 2
E000
0000–FFFF
--
5-77
L09.06
Output Contact (MC-MB-MA) Select
00: Disabled (No Fault Relay)
01: Enabled (Fault Relay Active)
01
00, 01
--
5-77
N02.01
AFR Tuning
1.00
0.00–10.00
--
5-80
N02.02
AFR Detection Time
50
0–2000
ms
5-80
N02.03
AFR Time Constant
750
0–2000
ms
5-80
N02.04
AFR Limit
5.0
0.0–60.0
Hz
5-80
N02.05
OLV Stabilization Level
00
00–11, FF
--
5-80
N06.01
Line-to-Line Motor Tuning
00: Disabled
01: Enabled
01
00–01
--
5-82
Parameter Parameter Name
Default
Range
Units
Reference
Page
* Parameters defaults changed by X-Press Programming
** Parameters changed by E01.03
*** Value depends on drive model
**** Default value depends on control method
Summary of Contents for 2001-G+M
