![background image](http://html1.mh-extra.com/html/magnetek/2001-g-m/2001-g-m_instruction-manual_3598661181.webp)
IMPULSE•G+ Mini Advanced Instruction Manual – March 2014
A-17
L02.01
Power-loss Selection
00: Disable
01: Enabled
02: CPU Power Active
00
00–02
--
5-63
L02.02
Power-loss Ride Thru Time
0.1 (Varies)
0.0–25.5
sec
5-63
L02.03
Power-loss Base Block Time
01. (Varies)
0.1–5.0
sec
5-63
L02.04
Power-loss V/f Ramp Time
0.3 (Varies)
0.0–5.0
sec
5-63
L02.05
PUV Detection Level
190/380
150–210
300–420
V
5-63
L02.07
Power-loss Ride Thru Accel
0.0
0.0–25.5
sec
5-63
L03.01
Stall Prevention Accel Select
00: Disabled
01: General Purpose
02: Intelligent
01
00–02
--
5-64
L03.02
Stall Prevention Accel Level
150
0–150
%
5-64
L03.03
Stall Prevention Constant HP Limit
50
0–100
%
5-66
L03.05
Stall Prevention Run Select
00: Disabled
01: Decel Time 1
02: Decel Time 2
01
00–02
--
5-67
L03.06
Stall Prevention Run Level
150
30–150
%
5-68
L03.17
DC Bus Voltage for Intelligent Control
370
150–400
V
5-69
L03.20
Main Circuit Voltage Gain
A01.02
0.00–5.00
--
--
L03.21
Deceleration Calculation Gain
A01.02
0.00–200.00
--
--
L03.23
Automatic Stall Prevention Selection
During Run
00: Sets the level to L03.04 throughout
the entire frequency range
01: Automatically lowers Stall
Prevention level during run in the
constant power range. The lower limit
will be 40% of L03.06.
00
00–01
--
5-69
L03.24
Motor Acceleration Time Inertial
Calculations
O02.04
0.001–10.000
--
5-69
L03.25
Load Inertia Ratio
1.0
0.0–1000.0
--
5-69
L04.01
Speed Agree Level ±
0.0
0.0–150.0
Hz
5-70
L04.02
Speed Agree Width ±
2.0
0.0–20.0
Hz
5-70
L04.03
Speed Agree Level ±
0.0
-150.0–150.0
Hz
5-70
L04.04
Speed Agree Width ±
2.0
0.0–20.0
Hz
5-70
L04.07
Speed Agree Detection
00: No detection during baseblock
01: Detection always enabled
00
00, 01
--
5-71
Parameter Parameter Name
Default
Range
Units
Reference
Page
* Parameters defaults changed by X-Press Programming
** Parameters changed by E01.03
*** Value depends on drive model
**** Default value depends on control method
Summary of Contents for 2001-G+M
