Liquid Controls LectroCount LCR 600 Installation-Parts Download Page 68

Page: 68 / 78

Installation

- 82184 -

Epson Printer Ground Wire Kit

Description

Part Number

Quantity

Ground Wire

84101

Terminal (.375 ring, 16GA)

71878

To ground an Epson printer:

1. Remove one of the mounting bolts that fasten the printer mounting brackets to the truck cab floor.

2. Place one end terminal of the ground wire over the mounting bolt and return the bolt to its original

place.

3. At the back of the Epson printer, remove the silver ground screw marked “FG”.

4. Place the other end terminal of the ground wire over the ground screw and return the screw to its

original place.

5. Check the strap for a good ground connection (see page 13).

Additional Terminal

that are not purchased from Liquid Controls.

Summary of Contents for LectroCount LCR 600















































































Search results

Summary of Contents for LectroCount LCR 600

Reviews:

Related manuals for LectroCount LCR 600

Brands by name

Popular brands

Liquid Controls LectroCount LCR 600, Installation-Parts

Search results

Summary of Contents for LectroCount LCR 600

Reviews:

Related manuals for LectroCount LCR 600

Brands by name

Popular brands