Liquid Controls LectroCount LCR 600 Installation-Parts Download Page 67

Page: 67 / 78

Installation

Routing Data Cables

See the instructions on

Routing LCD 600 Data and Power Cables

for routing the data cable from

the back of the truck to the cab.

Disconnect Power

Disconnect the power before working on the CPU board.

RS-232 Communication

To communicate by means of genuine RS-232 protocol, the +VP Red wire must be connected to the
J3 terminal block at terminal 47 (not 46).

To install the printer:

1. Find a convenient mounting spot in the truck cab where drivers can easily operate the printer.

2. Clean the mounting spot and the bottom of the printer with alcohol for the best stick.

3. Attach the Velcro to the mounting spot and the bottom of the printer and fasten the printer to the

mounting spot.

4. Connect the data cable to the RS-232 data port on the back of the printer.

Connecting Power

To connect power to the printer, see

Power Supply

Epson Printer Ground Wire Kit Installation

Before connecting power to the LCR 600 and the Epson printer, ground the printer to the truck cab floor.
Epson printers sold for truck installations are all grounded in the same manner.

Summary of Contents for LectroCount LCR 600















































































Search results

Summary of Contents for LectroCount LCR 600

Reviews:

Related manuals for LectroCount LCR 600

Brands by name

Popular brands

Liquid Controls LectroCount LCR 600, Installation-Parts

Search results

Summary of Contents for LectroCount LCR 600

Reviews:

Related manuals for LectroCount LCR 600

Brands by name

Popular brands