Leviton NorthStar Site Controller User Manual Download Page 3

Page: 3 / 65

TABLE OF CONTENTS

1 Introduction

..........................................................................................

1.1 The NorthStar Lighting Solution ..................................................

1.2

Key

Beneﬁts

................................................................................

1.3

System

Requirements

................................................................

1.4 Supported Lighting Controllers ...................................................

2 Installation and Initial Setup ...............................................................

2.1

System

Requirements

................................................................

2.2 Lighting System Conﬁguration Overview ....................................

2.3 Methods for New Installations .....................................................

2.3.1 Use the Leviton Lighting Installer app ................................

2.3.2 Install Hardware and Discover Unconﬁgured Devices .......

2.3.3 Create and Import a .CSV ﬁle ............................................

2.3.4

Enter

Everything

Manually

.................................................

2.4 The NorthStar Site Controller .....................................................

2.4.1 Buttons on the NorthStar Site Controller ............................

2.4.2 Setting Up the NorthStar Site Controller ............................

2.5 Establishing a Connection to the Site Controller ........................

2.5.1

Accessing

the

Site

Controller

.............................................

2.5.2

Logging

...........................................................................

3 Navigating the User Interface ................................................................

3.1

The

Dashboard

...........................................................................

3.2

Devices

Page

..............................................................................

3.3 Understanding Zones, Behaviors, and Scenes ..........................

4 Conﬁguration ..........................................................................................

4.1 Basic Site Conﬁguration .............................................................

4.1.1 Conﬁguring the Site Controller's Location ..........................

4.1.2 Enabling or Disabling Ofﬂine Maps ....................................

4.1.3 Conﬁguring the System Date and Time ..............................

4.2 Set and Encrypt the SNAP Communications Channel ...............

4.3 Changing Wi-Fi Settings .............................................................

4.4 Factory Defaulting Network Settings ..........................................

4.5 Conﬁguring Zones and Scenes ..................................................

4.5.1

Adding

Zones

.....................................................................

4.5.2

Adding

Scenes

...................................................................

4.6 Conﬁguring Lights and Sensors ..................................................

4.6.1 Information Fields for Lights and Sensors ..........................

4.6.2

Adding

Lights

......................................................................

4.6.3

Adding

Sensors

..................................................................

WEB

VERSION

Summary of Contents for NorthStar Site Controller


































































Search results

Summary of Contents for NorthStar Site Controller

Reviews:

Related manuals for NorthStar Site Controller

Brands by name

Popular brands

Leviton NorthStar Site Controller, User Manual

Search results

Summary of Contents for NorthStar Site Controller

Reviews:

Related manuals for NorthStar Site Controller

Brands by name

Popular brands