Leviton NorthStar Site Controller User Manual Download Page 55 | Manualshive

Page: 55 / 65

background image

7 ADMINISTRATION

54

To update the NorthStar site controller using the System Upgrade button:

1.

Log in to the site controller you wish to update, then click

Conﬁg - Backup/

Restore

to open the

Backup/Restore

tab.

2.

Verify you have a current backup of your system. For more information on
backing up the system, see Backing up and restoring a system conﬁguration on
page 55.

3. Obtain the new NorthStar update ﬁle from Leviton.

4.

Click the

System Upgrade

button. When the pop up menu appears, click

System Upgrade

again to conﬁrm your intention to upgrade.

5.

Browse to and select the update ﬁle, then click

Open

to start the update

process. The lights on the site controller will blink continuously during the
update. If the lights ﬂash red, contact Leviton Customer Support for possible
solutions.

6.

After the lights have stopped ﬂashing green for at least ﬁve minutes, unplug the
USB drive and power cycle the controller.

NOTE:

During an update, the lighting controllers will blink their corresponding lights

when each individual update is completed.

To update the NorthStar site controller using an update drive:

1.

Verify you have a current backup of your system. For more information on
backing up the system, see Backing up and restoring a system conﬁguration on
page 55.

2. Obtain the new NorthStar USB update drive from Leviton.

3.

Plug the USB drive into the USB port on the site controller. This will begin the
update process, which may take several minutes.

4.

If the lights on the site controller ﬂash green, the update was successful. If the
lights ﬂash red, contact Leviton Customer Support for possible solutions.

5.

After the lights stop ﬂashing green, unplug the USB drive and power cycle the
controller.

7.6 Rebooting the Site Controller

If you ever need to reboot a site controller, this is accomplished through the
NorthStar interface without the need to be present at the site controller.

To reboot the site controller:

1.

Log in to the site controller you wish to reboot, then click

Conﬁg - System

to

open the

System

tab.

2.

Click the

Reboot Site Controller

button to open the reboot site controller pop

up window, then click

Reboot

to reboot the site controller, or

Cancel

to exit

without rebooting.

WEB

VERSION

«
...
53
54
55
56
57
...
»

Summary of Contents for NorthStar Site Controller


































































Reviews:

No comments

Related manuals for NorthStar Site Controller

DELTAFLUX MT100

Brand: PIETRO FIORENTINI Pages: 16

Brand: Watts Pages: 2

Brand: VAT Pages: 29

Brand: Balboa Instruments Pages: 19

Brand: +GF+ Pages: 3

Brand: Össur Pages: 58

Brand: Vag Pages: 15

Brand: Telit Wireless Solutions Pages: 45

Brand: YOKOGAWA Pages: 33

Brand: Intermatic Pages: 3

Brand: hotset Pages: 2

Brand: M-system Pages: 5

Brand: Satel Pages: 7

Brand: Airmar Technology Corporation Pages: 4

Brand: Motorline professional Pages: 8

Brand: Swagelok Pages: 20

Brand: V-ZUG Pages: 24

Brand: J+J Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands