Lenovo ThinkSystem SR850 V2 Service Manual Download

Page: 68 / 288

This message is for the use case when an implementation has detected a recovery from a Front Panel NMI
/ Diagnostic Interrupt

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: Critical - Other
SNMP Trap ID: 50
CIM Prefix: PLAT CIM ID: 0223

User Action:

Information only; no action is required

Service Action:

Information only; no action is required.

•

FQXSPIO2004I: Bus [SensorElementName] has recovered from a bus timeout.

This message is for the use case when an implemenation has detected that a system has recovered from
a Bus Timeout.

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: Critical - Other
SNMP Trap ID: 50
CIM Prefix: PLAT CIM ID: 0225

User Action:

Information only; no action is required

Service Action:

Information only; no action is required.

•

FQXSPIO2006I: System [ComputerSystemElementName] has recovered from an NMI.

This message is for the use case when an implementation has detected a Software NMI has been
Recovered from.

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: Critical - Other
SNMP Trap ID: 50
CIM Prefix: PLAT CIM ID: 0230

User Action:

Information only; no action is required

Service Action:

Information only; no action is required.

•

FQXSPIO2007I: A PCI PERR recovery has occurred on system [ComputerSystemElementName].

ThinkSystem SR850 V2 System Events Service Guide

Summary of Contents for ThinkSystem SR850 V2

































































































































































































































































































Search results

Summary of Contents for ThinkSystem SR850 V2

Reviews:

Related manuals for ThinkSystem SR850 V2

Brands by name

Popular brands

Lenovo ThinkSystem SR850 V2, Service Manual

Search results

Summary of Contents for ThinkSystem SR850 V2

Reviews:

Related manuals for ThinkSystem SR850 V2

Brands by name

Popular brands