Lenovo ThinkSystem SR850 V2 Service Manual Download Page 75

Page: 75 / 288

7. If problem persists, collect Service Data log.

8. Contact Lenovo Support.

Service Action:

uefi_defined

•

FQXSPMA0024G: Sensor [SensorElementName] has asserted.

This message is for the use case when an implementation has detected a Sensor has asserted.

Severity: Warning
Serviceable: No
Automatically notify Support: No
Alert Category: Warning - Memory
SNMP Trap ID: 43
CIM Prefix: PLAT CIM ID: 0508

User Action:

Complete the following steps:

1. If the DIMM configuration was changed prior to this failure verify that the DIMMs are installed in the

correct population sequence.

2. RESEAT the DIMM that failed POST memory test and the DIMMs on adjacent slots if populated. Boot

to F1 setup and enable the DIMM. Reboot the system.

3. If the DIMMs have been upgraded just prior to the issue than update uEFI to the latest version.

4. If the problem persists, collect Service Data logs.

5. Contact Lenovo Support.

Service Action:

uefi_defined

•

FQXSPMA0025I: Sensor [SensorElementName] has asserted.

This message is for the use case when an implementation has detected a Sensor has asserted.

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: System - Other
SNMP Trap ID:
CIM Prefix: PLAT CIM ID: 0508

User Action:

Information only; no action is required

Service Action:

Information only; no action is required

•

FQXSPMA2005I: The System [ComputerSystemElementName] has detected a POST Error

deassertion.

This message is for the use case when an implementation has detected that Post Error has deasserted.

Chapter 2

XClarity Controller events

Summary of Contents for ThinkSystem SR850 V2

































































































































































































































































































Search results

Summary of Contents for ThinkSystem SR850 V2

Reviews:

Brands by name

Popular brands

Lenovo ThinkSystem SR850 V2, Service Manual

Search results

Summary of Contents for ThinkSystem SR850 V2

Reviews:

Brands by name

Popular brands