Lenovo ThinkSystem SR850 V2 Service Manual Download Page 267

Page: 267 / 288

•

FQXPMSD0010M: uEFI is timeout while LXPM send command to test hard drive.

Severity: Error

User Action:

1. Reboot system and run the test again later.

2. If this message is still reported, please run the latest version of SMART tool on OS which is open

source tool and could be downloaded from website to check hard drive status.

3. If the problem persists, please contact technical support.

Service Action:

1. Review PD Steps.

2. Verify HDD firmware.

3. Replace the hard drive

4. If problem persists, escalate to next level of support

•

FQXPMSD0011M: The hard drive is not supported by uEFI while LXPM send command to test hard

drive.

Severity: Error

User Action:

1. Please check hard drive specification to see if the hard drive support ATA self-test feature.

2. If the problem persists, please contact technical support.

Service Action:

1. Review PD Steps.

2. Verify HDD firmware.

3. Replace the hard drive

4. If problem persists, escalate to next level of support

•

FQXPMSR0001K: Found unsupported RAID adapter.

Severity: Warning

User Action:

1. Check the following Lenovo support site for information on supported RAID adapters. http://www.

lenovo.com/us/en/serverproven/index.shtml

2. Ensure RAID adapter, LXPM, and UEFI firmware are at the latest levels.

3. If the problem persists, please contact technical support.

Service Action:

1. Review PD Steps.

2. Verify PD steps.

3. If problem persists, escalate to next level of support

•

FQXPMSR0011K: Failed to change disk drives' state.

Severity: Warning

Chapter 4

XClarity Provisioning Manager events

263

Summary of Contents for ThinkSystem SR850 V2

































































































































































































































































































Search results

Summary of Contents for ThinkSystem SR850 V2

Reviews:

Brands by name

Popular brands

Lenovo ThinkSystem SR850 V2, Service Manual

Search results

Summary of Contents for ThinkSystem SR850 V2

Reviews:

Brands by name

Popular brands