Lenovo ThinkSystem SR850 V2 Service Manual Download Page 70

Page: 70 / 288

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: Warning - Other
SNMP Trap ID: 60
CIM Prefix: PLAT CIM ID: 0247

User Action:

Information only; no action is required

•

FQXSPMA0002N: Configuration Error for [PhysicalMemoryElementName] on Subsystem

[MemoryElementName].

This message is for the use case when an implementation has detected a Memory DIMM configuration
error has been corrected.

Severity: Error
Serviceable: Yes
Automatically notify Support: No
Alert Category: Critical - Memory
SNMP Trap ID: 41
CIM Prefix: PLAT CIM ID: 0126

User Action:

Complete the following steps:

1. If the DIMM configuration was changed prior to this failure verify that the DIMMs are installed in the

correct population sequence.

2. RESEAT the DIMM that failed POST memory test and the DIMMs on adjacent slots if populated. Boot

to F1 setup and enable the DIMM. Reboot the system.

3. If the DIMMs have been upgraded just prior to the issue than update uEFI to the latest version.

4. If the problem persists, collect Service Data logs.

5. Contact Lenovo Support.

Service Action:

uefi_defined

•

FQXSPMA0005N: Subsystem [MemoryElementName] has insufficient memory for operation.

This message is for the use case when an implementation has detected that the usable Memory is
insufficient for operation.

Severity: Error
Serviceable: Yes
Automatically notify Support: No
Alert Category: Critical - Memory
SNMP Trap ID: 41
CIM Prefix: PLAT CIM ID: 0132

User Action:

Complete the following steps:

1. Ensure one or more DIMMs are installed in the server.

2. Resolve existing memory errors if they are present.

ThinkSystem SR850 V2 System Events Service Guide

Summary of Contents for ThinkSystem SR850 V2

































































































































































































































































































Search results

Summary of Contents for ThinkSystem SR850 V2

Reviews:

Brands by name

Popular brands

Lenovo ThinkSystem SR850 V2, Service Manual

Search results

Summary of Contents for ThinkSystem SR850 V2

Reviews:

Brands by name

Popular brands