manualshive.com logo in svg

Lenovo ThinkSystem SR850 V2, Service Manual

Share
Download
Lenovo ThinkSystem SR850 V2 Service Manual Download Page 257

Service Action:

1.  Review PD Steps.

2.  Clear RAID configuration using UEFI Setup (e.g. RAID utility in UEFI HII).

3.  If problem persists, escalate to next level of support.

• 

FQXPMER0003I: RAID configuration cleared successfully 

Severity: Info

User Action:

Information only; no action is required.

Service Action:

n/a

• 

FQXPMER0003M: Failed to erase internal storage drives 

Severity: Error

User Action:

1.  Ensure the proper connection of hard drives, backplane, and related cables.

2.  Check if security function is enabled for the hard disk drives, if yes, disable that and retry the 

operation.

3.  Ensure device firmware is at the latest level.

4.  Restart the system and retry the operation again.

5.  If the problem persists, contact technical support.

Service Action:

1.  Review PD Steps.

2.  Remove the failed drives.

3.  If problem persists, escalate to next level of support.

• 

FQXPMER0004I: Internal storage drives erased successfully 

Severity: Info

User Action:

Information only; no action is required.

Service Action:

n/a

• 

FQXPMER0004M: Failed to clear system logs 

Severity: Error

User Action:

1.  Restart BMC via supported method and reboot the system.

2.  Retry this operation again.

Chapter 4

.

XClarity Provisioning Manager events

253

Summary of Contents for ThinkSystem SR850 V2

































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands