manualshive.com logo in svg

Lenovo ThinkSystem SR850 V2, Service Manual

Share
Download
Lenovo ThinkSystem SR850 V2 Service Manual Download Page 189

Table 3. Events organized by severity (continued)

Event ID

Message String

Severity

FQXSFPU4059I

User requested to skip freezing lock of AHCI-attached SATA drives. 
System UEFI accepted the request and will execute priot to OS boot.

Informational

FQXSFPU4060I

Skipped freezing lock of AHCI-attached SATA drives.

Informational

FQXSFPU4061I

Restored default locking behavior of AHCI-attached SATA drives.

Informational

FQXSFPU4080I

Host Power-On password has been changed.

Informational

FQXSFPU4081I

Host Power-On password has been cleared.

Informational

FQXSFPU4082I

Host Admin password has been changed.

Informational

FQXSFPU4083I

Host Admin password has been cleared.

Informational

FQXSFPU4084I

Host boot order has been changed.

Informational

FQXSFPU4085I

Host WOL boot order has been changed.

Informational

FQXSFSM0007I

The XCC System Event log (SEL) is full.

Informational

FQXSFSR0002I

[arg1] GPT corruption recovered, DiskGUID: [arg2]

Informational

FQXSFDD0001G

DRIVER HEALTH PROTOCOL: Missing Configuration. Requires 
Change Settings From F1.

Warning

FQXSFDD0002M

DRIVER HEALTH PROTOCOL: Reports 'Failed' Status Controller.

Warning

FQXSFDD0003I

DRIVER HEALTH PROTOCOL: Reports 'Reboot' Required Controller.

Warning

FQXSFDD0005M

DRIVER HEALTH PROTOCOL: Disconnect Controller Failed. Requires 
'Reboot'.

Warning

FQXSFDD0006M

DRIVER HEALTH PROTOCOL: Reports Invalid Health Status Driver.

Warning

FQXSFDD0007G

Security Key Lifecycle Manager (SKLM) IPMI Error.

Warning

FQXSFIO0008M

An intra-board UPI dynamic link width reduction has been detected 
on the link between processor [arg1] port [arg2] and processor [arg3] 
port [arg4].

Warning

FQXSFIO0009M

An inter-board UPI dynamic link width reduction has been detected 
on the link between processor [arg1] port [arg2] and processor [arg3] 
port [arg4].

Warning

FQXSFIO0013I

The device found at Bus [arg1] Device [arg2] Function [arg3] could not 
be configured due to resource constraints. The Vendor ID for the 
device is [arg4] and the Device ID is [arg5]. The physical slot number 
is [arg6].

Warning

FQXSFIO0016M

IFM: Reset loop avoided - Multiple resets not allowed.

Warning

FQXSFMA0012L

The [arg1] PFA Threshold limit has been exceeded on DIMM [arg2] at 
address [arg3]. [arg4]

Warning

FQXSFMA0016M

Memory spare copy failed. [arg1]

Warning

FQXSFMA0027M

DIMM [arg1] Self-healing, attempt post package repair (PPR) failed at 
Rank [arg2] Sub Rank [arg3] Bank [arg4] Row [arg5] on Device [arg6]. 
[arg7]

Warning

FQXSFMA0028M

DIMM [arg1] Self-healing, attempt post package repair (PPR) 
exceeded DIMM level threshold [arg2] at Rank [arg3] Sub Rank [arg4] 
Bank [arg5] Row [arg6] on Device [arg7]. [arg8]

Warning

Chapter 3

.

UEFI events

185

Summary of Contents for ThinkSystem SR850 V2

































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands