Lenovo ThinkSystem SR850 V2 Service Manual Download Page 23

Page: 23 / 288

Table 2. Events organized by severity (continued)

Event ID

Message String

Severity

FQXSPWD0001I

Reboot of system [ComputerSystemElementName] initiated by
watchdog [WatchdogElementName].

Informational

FQXSPWD0002I

Powering off system [ComputerSystemElementName] initiated by
watchdog [WatchdogElementName].

Informational

FQXSPWD0003I

Power cycle of system [ComputerSystemElementName] initiated by
watchdog [WatchdogElementName].

Informational

FQXSPWD0004I

Watchdog Timer interrupt occurred for [WatchdogElementName].

Informational

FQXSPBR4001I

Running the backup Management Controller [arg1] main application.

Warning

FQXSPCA0007J

Numeric sensor [NumericSensorElementName] going high (upper
non-critical) has asserted.

Warning

FQXSPCA0015J

Sensor [SensorElementName] has transitioned from normal to non-
critical state.

Warning

FQXSPDM4002I

Device [arg1] VPD is not valid.

Warning

FQXSPEA0001J

Sensor [SensorElementName] has transitioned from normal to non-
critical state.

Warning

FQXSPIO0014J

Bus [SensorElementName] is operating in a degraded state.

Warning

FQXSPIO2000J

The connector [PhysicalConnectorElementName] has been
disconnected.

Warning

FQXSPMA0010J

[PhysicalMemoryElementName] on Subsystem
[MemoryElementName] Throttled.

Warning

FQXSPMA0011G

Memory Logging Limit Reached for [PhysicalMemoryElementName]
on Subsystem [MemoryElementName].

Warning

FQXSPMA0024G

Sensor [SensorElementName] has asserted.

Warning

FQXSPNM4010I

DHCP[[arg1]] failure, no IP address assigned.

Warning

FQXSPNM4032I

DHCPv6 failure, no IP address assigned.

Warning

FQXSPPP4009I

The measured power value exceeded the power cap value.

Warning

FQXSPPP4010I

The new minimum power cap value exceeded the power cap value.

Warning

FQXSPPU0002G

The Processor [ProcessorElementName] is operating in a Degraded
State.

Warning

FQXSPPW0003G

Failure predicted on [PowerSupplyElementName].

Warning

FQXSPPW0006I

[PowerSupplyElementName] has lost input.

Warning

FQXSPPW0031J

Numeric sensor [NumericSensorElementName] going low (lower non-
critical) has asserted.

Warning

FQXSPPW0057J

Sensor [SensorElementName] has transitioned from normal to non-
critical state.

Warning

FQXSPPW0101J

Redundancy Degraded for [RedundancySetElementName] has
asserted.

Warning

FQXSPPW0104J

Non-redundant:Sufficient Resources from Redundancy Degraded or
Fully Redundant for [RedundancySetElementName] has asserted.

Warning

FQXSPSD0002G

Failure Predicted on [StorageVolumeElementName] for array
[ComputerSystemElementName].

Warning

Chapter 2

XClarity Controller events

Summary of Contents for ThinkSystem SR850 V2

































































































































































































































































































Search results

Summary of Contents for ThinkSystem SR850 V2

Reviews:

Brands by name

Popular brands

Lenovo ThinkSystem SR850 V2, Service Manual

Search results

Summary of Contents for ThinkSystem SR850 V2

Reviews:

Brands by name

Popular brands