manualshive.com logo in svg

Lenovo ThinkSystem SR850 V2, Service Manual

Share
Download
Lenovo ThinkSystem SR850 V2 Service Manual Download Page 123

Service Action:

uefi_defined

• 

FQXSPPU0011N: An SM BIOS Uncorrectable CPU complex error for [ProcessorElementName] has 

asserted. 

This message is for the use case when an SM BIOS Uncorrectable CPU complex error has asserted.

Severity: Error
Serviceable: Yes
Automatically notify Support: No
Alert Category: Critical - CPU
SNMP Trap ID: 40
CIM Prefix: PLAT CIM ID: 0816

User Action:

Complete the following steps:  

1.  Check Lenovo support site for an applicable service bulletin or UEFI firmware update that applies to 

this error.

2.  Reboot system.

3.  If problem persists, collect Service Data log.

4.  Contact Lenovo Support.

Service Action:

uefi_defined

• 

FQXSPPU2000I: [ProcessorElementName] in slot [SlotElementName] has been removed. 

This message is for the use case when an implementation has detected a Processor has been Removed.

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: System - Other
SNMP Trap ID: 
CIM Prefix: PLAT CIM ID: 0035

User Action:

Information only; no action is required.

Service Action:

Information only; no action is required.

• 

FQXSPPU2001I: An Over-Temperature Condition has been removed on [ProcessorElementName]. 

This message is for the use case when an implementation has detected a Over-Temperature Condition 
has been Removed for Processor.

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: Critical - Temperature

Chapter 2

.

XClarity Controller events

119

Summary of Contents for ThinkSystem SR850 V2

































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands