Lenovo ThinkSystem SR850 V2 Service Manual Download Page 26

Page: 26 / 288

Table 2. Events organized by severity (continued)

Event ID

Message String

Severity

FQXSPPW0110M

Non-redundant:Insufficient Resources for
[RedundancySetElementName] has asserted.

Error

FQXSPSD0001L

The [StorageVolumeElementName] has been disabled due to a
detected fault.

Error

FQXSPSD0002L

Drive [arg1] in the enclosure/chassis(MTM-SN: [arg2]) has been
disabled due to a detected fault.

Error

FQXSPSD0005L

Array [ComputerSystemElementName] is in critical condition.

Error

FQXSPSD0006L

Array [ComputerSystemElementName] has failed.

Error

FQXSPSD0007L

Array critical asserted on drive [arg1] in the enclosure/chassis (MTM-
S/N: [arg2]).

Error

FQXSPSD0008L

Array failed on drive [arg1] in the enclosure/chassis (MTM-S/N: [arg2]).

Error

FQXSPSE4000I

Certificate Authority [arg1] has detected a [arg2] Certificate Error.

Error

FQXSPSE4006I

SSL data in the Management Controller [arg1] configuration data is
invalid. Clearing configuration data region and disabling SSL.

Error

FQXSPSR0001N

Sensor [SensorElementName] has transitioned to non-recoverable
from a less severe state.

Error

FQXSPUN0019M

Sensor [SensorElementName] has transitioned to critical from a less
severe state.

Error

FQXSPUN0023N

Sensor [SensorElementName] has transitioned to non-recoverable.

Error

FQXSPUP0007L

Invalid or Unsupported firmware or software was detected on system
[ComputerSystemElementName].

Error

FQXSPUP4000I

Please ensure that the Management Controller [arg1] is flashed with
the correct firmware. The Management Controller is unable to match
its firmware to the server.

Error

FQXSPUP4003I

[arg1] firmware mismatch internal to system [arg2]. Please attempt to
flash the [arg3] firmware.

Error

FQXSPUP4004I

XCC firmware mismatch between nodes/servers [arg1] and [arg2].
Please attempt to flash the XCC firmware to the same level on all
nodes/servers.

Error

FQXSPUP4005I

FPGA firmware mismatch between nodes/servers [arg1] and [arg2].
Please attempt to flash the FPGA firmware to the same level on all
nodes/servers.

Error

List of XClarity Controller events

This section lists all messages that can be sent from the XClarity Controller.

•

FQXSPBR4000I: Management Controller [arg1]: Configuration restored from a file by user [arg2].

This message is for the use case where a user restores a Management Controller configuration from a file.

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: none
SNMP Trap ID:

ThinkSystem SR850 V2 System Events Service Guide

Summary of Contents for ThinkSystem SR850 V2

































































































































































































































































































Search results

Summary of Contents for ThinkSystem SR850 V2

Reviews:

Brands by name

Popular brands

Lenovo ThinkSystem SR850 V2, Service Manual

Search results

Summary of Contents for ThinkSystem SR850 V2

Reviews:

Brands by name

Popular brands