Lenovo ThinkAgile HX2320 Appliance User Manual Download Page 3

Page: 3 / 100

Contents

Chapter 1. Introduction . . . . . . . . . 1

Typical Nutanix architecture .  .  .  .  .  .  .  .  .  .  .  2
HX deployment architecture .  .  .  .  .  .  .  .  .  .  .  2
Understanding appliances and certified nodes .  .  .  .  2
Identifying your server .  .  .  .  .  .  .  .  .  .  .  .  .  3
Specifications .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  4
Management options.  .  .  .  .  .  .  .  .  .  .  .  .  10

Chapter 2. Server components . . . . 13

Front view .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  13
Operator information panel .  .  .  .  .  .  .  .  .  .  14
Rear view .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  16
Rear view LEDs .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  19
System board components .  .  .  .  .  .  .  .  .  .  20
System board LEDs .  .  .  .  .  .  .  .  .  .  .  .  .  22
Parts list.  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  22

Power cords . . . . . . . . . . . . . . 26

Chapter 3. Network/Infrastructure
Planning . . . . . . . . . . . . . . . . 27

Chapter 4. Server setup checklist. . . 29

Server package contents . . . . . . . . . . . 29
Cable the server

. . . . . . . . . . . . . . 30

Power on the server . . . . . . . . . . . . . 31

Power off the server . . . . . . . . . . . 31

Set the network connection for the Lenovo XClarity
Controller . . . . . . . . . . . . . . . . . 31

Chapter 5. Installing and configuring
a cluster on ThinkAgile HX Series
servers . . . . . . . . . . . . . . . . . 33

Chapter 6. Installing and setting up
Lenovo XClarity Administrator. . . . . 35

Deploying Lenovo XClarity Administrator . . . . . 35
Managing ThinkAgile HX Series servers . . . . . 35

Chapter 7. Installing and setting up
Lenovo XClarity Integrator. . . . . . . 37

Deploying Lenovo XClarity Integrator for VMware
vCenter . . . . . . . . . . . . . . . . . . 37

Chapter 8. Hardware replacement
procedures . . . . . . . . . . . . . . . 39

Installation Guidelines . . . . . . . . . . . . 39

System reliability guidelines .  .  .  .  .  .  .  .  40
Working inside the server with the power on .  .  41
Handling static-sensitive devices .  .  .  .  .  .  41

Hot-swap drive replacement . . . . . . . . . . 43

Remove a hot-swap drive . . . . . . . . . 43
Install a hot-swap drive . . . . . . . . . . 44

Hot-swap power supply replacement . . . . . . 45

Remove a hot-swap power supply. . . . . . 46
Install a hot-swap power supply

. . . . . . 51

System fan replacement . . . . . . . . . . . 57

Remove a system fan . . . . . . . . . . . 57
Install a system fan. . . . . . . . . . . . 58

RAID adapter (HBA) replacement . . . . . . . . 60

Remove the RAID adapter . . . . . . . . . 60
Install the RAID adapter . . . . . . . . . . 61

LOM adapter replacement

. . . . . . . . . . 62

Remove the LOM adapter . . . . . . . . . 63
Install the LOM adapter . . . . . . . . . . 64

PCIe adapter replacement. . . . . . . . . . . 65

Remove a PCIe adapter . . . . . . . . . . 65
Install a PCIe adapter . . . . . . . . . . . 66

DIMM replacement . . . . . . . . . . . . . 67

Remove a DIMM. . . . . . . . . . . . . 68
DIMM installation rules . . . . . . . . . . 69
Install a DIMM

. . . . . . . . . . . . . 74

M.2 backplane and M.2 drive replacement . . . . 76

Remove the M.2 backplane and M.2 drive.  .  .  76
Adjust the retainer on the M.2 backplane .  .  .  77
Install the M.2 backplane and M.2 drive.  .  .  .  78

Chapter 9. Updating firmware. . . . . 83

Appendix A. Configuration
procedures . . . . . . . . . . . . . . . 87

Appendix B. Getting help and
technical assistance . . . . . . . . . . 89

Appendix C. Trademarks . . . . . . . 91

Index . . . . . . . . . . . . . . . . . . 93

Summary of Contents for ThinkAgile HX2320 Appliance





































































































Search results

Summary of Contents for ThinkAgile HX2320 Appliance

Reviews:

Related manuals for ThinkAgile HX2320 Appliance

Brands by name

Popular brands

Lenovo ThinkAgile HX2320 Appliance, User Manual

Search results

Summary of Contents for ThinkAgile HX2320 Appliance

Reviews:

Related manuals for ThinkAgile HX2320 Appliance

Brands by name

Popular brands