Lenovo ThinkAgile HX2320 Appliance User Manual Download Page 42

Page: 42 / 100

Note:

Make sure that you connect to VMware vCenter Server Appliance using port 9443 when you

are working with Lenovo XClarity Integrator.

Information about configuring Lenovo XClarity Integrator is available at:

http://sysmgt.lenovofiles.com/help/topic/com.lenovo.lxci_vcenter.doc/vcenter_install_config_lxci.html

Step 4. Manage the cluster by requesting access to the BMC of each of the servers in the cluster.

Information about requesting BMC access is available at:

http://sysmgt.lenovofiles.com/help/topic/com.lenovo.lxci_vcenter.doc/vcenter_using_vsphere_web_
client_request_imm_access.html

User Guide for ThinkAgile HX2320 Appliance and HX2321 Node

Summary of Contents for ThinkAgile HX2320 Appliance





































































































Search results

Summary of Contents for ThinkAgile HX2320 Appliance

Reviews:

Related manuals for ThinkAgile HX2320 Appliance

Brands by name

Popular brands

Lenovo ThinkAgile HX2320 Appliance, User Manual

Search results

Summary of Contents for ThinkAgile HX2320 Appliance

Reviews:

Related manuals for ThinkAgile HX2320 Appliance

Brands by name

Popular brands