Lenovo ThinkAgile HX2320 Appliance User Manual Download Page 25

Page: 25 / 100

Figure 10. System board components

Serial-port-module connector

RAID adapter slot (slot 4)

BIOS ROM programming connector

Riser 1 slot

LOM adapter connector

XCC ROM programming connector

Front USB connector

Operator-information-panel connector

Rear-backplane power connector

Front VGA connector

TCM

/TPM

connector (for China only)

Processor 1 socket

DIMM slots (24)

System fan 1 connector

System fan 2 connector

System fan 3 connector

System fan 4 connector

System fan 5 connector

System fan 6 connector

System fan 7 connector

Processor 2 socket

Front-backplane power connector

NVMe 2-3 connector

NVMe 0-1 connector

CMOS battery

M.2 module slot (SATA/PCIe slot 5)

Riser 2 slot

Notes:

•

Trusted Cryptography Module

Chapter 2

Server components

Summary of Contents for ThinkAgile HX2320 Appliance





































































































Search results

Summary of Contents for ThinkAgile HX2320 Appliance

Reviews:

Related manuals for ThinkAgile HX2320 Appliance

Brands by name

Popular brands

Lenovo ThinkAgile HX2320 Appliance, User Manual

Search results

Summary of Contents for ThinkAgile HX2320 Appliance

Reviews:

Related manuals for ThinkAgile HX2320 Appliance

Brands by name

Popular brands