manualshive.com logo in svg

LEGRAND 48DCWC-04-2X100-D0NB, User Manual

Share
Download
LEGRAND 48DCWC-04-2X100-D0NB User Manual Download Page 170

 

 

PRO1 Sentry Switched DC PDU 

170 of 211 

set line 

Sets line configuration values. 

Command Syntax 

set line email [disabled | enabled] <name | id | ALL> 
set line load [alarmhi | alarmlo | warnhi | warnlo] <name | id | ALL>  <value> 
set line load hyst <value> 
set line snmpt [disabled | enabled] <name | id | ALL> 

Parameters 

The 

set line

 command uses the following parameters: 

Email 

Email notification for line events. 

Hyst 

Hysteresis between event state and recovery.  

Load 

Current load for a line. min = 0A, max (current limit) in 

show lines

 command, 

hyst 0.0-10.0A (default 1.0A). 

SNMPT 

SNMP trap notifications for line events. 

Sub-Parameters 

The 

set line

 command uses the following sub-parameters: 

alarmhi 

High alarm value. 

alarmlo 

Low alarm value. 

warnhi 

High warning alarm. 

warnlo 

Low warning alarm. 

 

min <= alarmlo <= warnlo <= warnhi <= alarmhi <= max 

Command Access 

Admin level only 

 

 

 

 

Summary of Contents for 48DCWC-04-2X100-D0NB




















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands