43
Sample List Screen
•
If the data does not exist, the measurement list screen will not be displayed.
•
For every data entry, the sample No. and name is displayed in the column above, and the measurement date
and time are displayed in the column below.
•
The cursor will appear at the currently selected sample.
•
Press the [Confirmation] key or [ESC] to bring up the Sample detail screen and display the currently selected
target’s detailed data.
•
Press [
] to select (move the cursor to) the previous sample.
•
Press [
] to select (move the cursor to) the following sample.
•
Press [
] to display the previous list screen. The cursor will move to the top sample number.
•
Press [
] to display the following list screen. The cursor will move to the top sample number.
Sample Detail Screen
•
If no data exists, the data value column will be blank.
•
The sample No. and name is displayed below the sample tab.
•
Failure to set Observer/Illuminant 2 will cause the data value column to be blank.
•
The measurement date and time as well as related target information will be displayed below the data value
column.
•
An exclamation mark
!
will be displayed in the lower-right corner of the screen for stored data even if a light
intensity decrease warning or measurement out-of-range warning occurs.
•
A display showing the overall page count and the position on the current page is available at the bottom of the
screen.
•
The number of pages to display is determined by the <Display type> setting.
•
Press [
] to display the previous sample.
•
Press [
] to display the following sample.
•
Press [
] to bring up the previously displayed page.
•
Press [
] to bring up the following displayed page.
Common Aspects of List and Detail Screens
•
The target No. and name displayed on the currently selected target details screen will be displayed to the right
of the Target tab.
•
Press [
] to bring up the Target screen.
•
Press [MENU] to bring up the <Sample menu> screen.
•
Pressing the measurement key/button will cause the <Measuring> screen to be displayed and measurement to
begin.
•
If calibration is required (if calibration has not yet been performed or if the calibration interval has been
exceeded), a message will be displayed prompting calibration. Select “OK” to bring up the calibration screen.
Selecting “Cancel” will cause the display to return to the previous screen without performing calibration.
•
If the maximum number of measurements has been reached, an error indication message will be displayed and
measurement will not be possible. Select “OK” to return to the previous screen.
•
When <Beep> is ON, the buzzer will go off once after successful completion and 3 times when an error occurs.
•
After successful completion of the measurement, the new data will be added to the end of the measurement
number.
•
If an error occurs during measurement, an error indication message will be displayed. Select “OK” to return to
the previous screen.
•
In general, the screen will return to the previous screen (page) after measurement. However, if the manual
average count is two or more, the Manual average screen will be displayed (refer to page 70).
Summary of Contents for CM-M6
