Konica Minolta CM-M6, Instruction Manual

Page: 58 / 128

55
„
Tolerance Settings
Specify the tolerance used for pass/fail judgment of measured data for each target color.
Operating Procedure Start the procedure from the <Target menu> - <Pass/Fail> screen.
1
Use [

] or [

] to move the cursor to “Edit
tolerance”, and then press the [Confirmation] key.
The tolerance list screen is displayed.
2
Use [

] or [

] to move the cursor to the item to be
set, and then press the [Confirmation] key.
The <Edit tolerance> screen is displayed.
3
Use [

]/[

] or [

]/[

] to move the cursor to the
item to set and press the [Confirmation] key to
change the item.
• When the selected item is not currently checked,
pressing the
[Confirmation] key causes the item to be
checked, after which the setting value can be changed.
• Press
[  ] or [  ]
to move the cursor to the setting value
area. Pressing the
[Confirmation] key
causes the cursor
to appear on the value. Press [

] or [

] to change the
value.
Move the cursor between the digits of the value by
pressing
[  ] or [  ]
.
Settings
„ {
ΔL*, Δa*, Δb*, ΔC*, ΔH*, ΔFF: -20.00 to 20.00
„ {
Other than the above: 0.00 to 20.00
• Press the [Confirmation] key to confirm every time the
setting of an item is changed.
Memo
If “Audi2000(ΔEc)” or “Audi2000(ΔEp)” is selected under
“Sample” - “Display type”, not only is moving between pages
possible with the [

] and [

] keys from the displayed page
when the <Edit tolerance> screen is selected, but if
Audi2000(ΔEc) or Audi2000(ΔEp) is enabled, in addition to
the tolerance for each angle, the tolerances for average
(mΔEc or mΔEp) and maximum (ΔEcMax or ΔEpMax) can also
be set. When setting the tolerance for mΔEc, mΔEp, ΔEcMax
or ΔEpMax, setting a value for any angle will cause that value
to be shown for all angles in the tolerance setting screen.
4
After all settings have been configured, use [

]/
[

] or [

]/[

] to move the cursor to “OK”, and
then press the [Confirmation] key.
The setting is confirmed and the screen returns to the
<Edit
tolerance> screen
.
If [ESC] is pressed during setup, the settings will not be changed
and the screen will return to the <Edit tolerance> screen .
5
Press [ESC] to return to the <Pass/Fail> screen.
Target menu [0002]
Pass/Fail
Target
Edit tolerance
Parametric coef.
Warning level
80%
Target
∆FF
∆L* ∆E*ab ∆C* ∆H*
-1.00 -1.00 -1.00 0.00
1.00 1.00 1.00 1.00
-1.00 -1.00 -1.00 0.00
1.00 1.00 1.00 1.00
-1.00 -1.00 -1.00 0.00
1.00 1.00 1.00 1.00
-1.00 -1.00 -1.00 0.00
1.00
0.00
1.00
0.00
1.00
1.00
-1.00
1.00
-1.00
1.00
1.00
-1.00
1.00
-1.00
1.00
1.00
-1.00
1.00
-1.00
1.00
1.00
-1.00
0002
TARGET-2
-15°
15°
25°
45°
75°
110°
10°/D65 None
1 2
Target
∆FF
∆L* ∆E*ab ∆C* ∆H*
-1.00 -1.00 -1.00 0.00
1.00 1.00 1.00 1.00
-1.00 -1.00 -1.00 0.00
1.00 1.00 1.00 1.00
-1.00 -1.00 -1.00 0.00
1.00 1.00 1.00 1.00
-1.00 -1.00 -1.00 0.00
1.00
0.00
1.00
0.00
1.00
1.00
-1.00
1.00
-1.00
1.00
1.00
-1.00
1.00
-1.00
1.00
1.00
-1.00
1.00
-1.00
1.00
1.00
-1.00
0002
TARGET-2
-15°
15°
25°
45°
75°
110°
1 10°/D65 2
None
Edit tolerance
-15°
+01.00
+00.00 ∆E*ab
∆L* +01.00
-00.00