KidKraft Cedar Summit F29080 Installation And Operating Instructions Manual Download

Page: 99 / 116

1 x Rebar Ground Stake

Step 47: Attach Ground Stake to TNR Upright

Hardware

1 x

#12 x 2” Pan Screw

Other Parts

Fig. 47.1

Rebar

Ground

Stake

Warning! To prevent tipping and avoid potential

injury, stakes must be driven 13”(330mm) into

ground. Digging or driving stakes can be

dangerous if you do not check first for under-

ground wiring, cables or gas lines.

In the spot shown in fig. 47.1 drive 1 Rebar Ground Stake 13” into the ground against the (9577) TNR

Ground Brace. Be careful not to hit the washer while hammering stake into the ground as this could cause the

washer to break off.

Attach the ground stake to (9577) TNR Ground Brace just below the bolt head using 1 (S7) #12 x 2” Pan

Screw as shown in fig. 47.1.

After driving stakes into the ground, check for sharp edges caused by the impact of the hammer. Smooth

any sharp edges from impact area and touch up with outdoor paint.

13” In

Ground

(330mm)

9577

Summary of Contents for Cedar Summit F29080





















































































































Search results

Summary of Contents for Cedar Summit F29080

Reviews:

Related manuals for Cedar Summit F29080

Brands by name

Popular brands

KidKraft Cedar Summit F29080, Installation And Operating Instructions Manual

Search results

Summary of Contents for Cedar Summit F29080

Reviews:

Related manuals for Cedar Summit F29080

Brands by name

Popular brands