manualshive.com logo in svg

KidKraft Cedar Summit F29080, Installation And Operating Instructions Manual

Share
Download
KidKraft Cedar Summit F29080 Installation And Operating Instructions Manual Download Page 110

 110 

 

  

AI-62
S5 X6(FW0)
S5 X2

Fig. 55.1

Fig. 55.2

Fig. 55.3

9286

Cafe Canopy

1-1/8”

AI-62
S5 X6(FW0)
S5 X2

w/#8 flat 

washer

S5

S5

Cafe Canopy 

Frame

x 1 per 

side

Hardware

5 x 

#8 x 1/2” Pan Screw (#8 flat washer)

2 x 

#8 x 1/2” Pan Screw

S5

S5

Other Parts

1 x Cafe Canopy Frame
1 x Cafe Canopy

A:

 Feed Cafe Canopy Frame through the pocket of the Cafe Canopy. (fig. 55.1)

B: 

With a helper hold the Canopy against the fort, centered over the door and window on (9286) Front Panel As-

sembly (fig. 55.1). Make sure the Cafe Canopy is smooth and tight then attach to the panel with 1 (S5) #8 x 1/2” 

Pan Screw (with #8 flat washer). Measure 1- 1/8” down from the first screw then attach a second screw and wash-

er. Follow measurements as shown in (fig. 55.2) to install 2 more screws and washers on the opposite side, then 

install one more screw in the top center of the canopy. Measurements must be exact. (Fig. 55.1& 55.2 & 55.3)

C: 

Hold the Cafe Canopy Frame against the panel and attach with 1 (S5) #8 x 1/2”  Pan Screw per side. (Fig.55.1 

& 55.2)

Step 55:  Attach Canopy

AI-62
S5 X6(FW0)
S5 X2

Summary of Contents for Cedar Summit F29080





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands